zoocros.blogg.se - Trimetric 2030 rv battery system monitor

TRIMETRIC 2030 RV BATTERY SYSTEM MONITOR GENERATOR
TRIMETRIC 2030 RV BATTERY SYSTEM MONITOR SERIAL
TRIMETRIC 2030 RV BATTERY SYSTEM MONITOR FULL

If desired a “battery reminders” lamp will flash to alert the user when this number exceeds a value programmable by user from 1 to 60 days.

TRIMETRIC 2030 RV BATTERY SYSTEM MONITOR FULL

This display will show you how long since they last received a full charge-measures from 0.01 day to over 600 days. To prolong their life, lead-acid batteries shouldn’t go too long between being fully charged. Only load amp-hours, by wiring the shunt in the desired current path.ĭays ago since batteries were last fully charged: It is also possible for this display to measure only total amp-hours produced by an energy source, such as solar array, or A flashing decimal point reminds you to multiply the reading by 1000 when the Amp-hour number exceeds 999. The display may be turned off (to darken display and for lowest current draw of 16 milliamps.)Īmp Hours from “full”: Shows actual “net” amp-hours removed from the battery from ☐.01 to☘0,000 amp-hours. The assumed BATTERY CAPACITY, upon which this display is based, can be programmed from 10-10,000 amp-hours. This is more accurate than other methods which do not use amp-hours to compute battery energy content (for example less expensive monitors which rely only on battery voltage to estimate energy content). This number is based on net-amp hour reading divided by the user programmable value of battery capacity. Speed of response: 1 second time constant. With 500A/50mV shunt measures from 0.1 to over 400 amps. With the 100A/100 mV shunt: measures 0.01 to over 70 amps. Resolution and maximum amps depends on choice of required shunt. Or the meter may be set up to measure only incoming energy from solar array or other energy source, or only load amps or watts if desired. Amps are accurate to ☑% ☑ least significant digit. You can choose to use either “amps” or “watts” to register the energy going in our out of the battery. Volts (only) can be read for optional second battery.īattery amps (or watts) on main batteries: For battery systems with nominal volts from 12 to 48V. Reads Battery volts 10.0-65.0V accurate to ± 0.2% ☑ least significant digit. Push SELECT to cycle through these: Battery volts of main and secondary batteries: The newer TM-2030 includes better lightning protection compared with the TM-2020.

TRIMETRIC 2030 RV BATTERY SYSTEM MONITOR SERIAL

(For the technically knowledgeable only) The TM-2030 has a serial data output of all the “real time” data-which could be used to access data for other control or output in, for example OEM applications.

The TM-2030 has a “simplified” level of operation suitable for most users, but can be configured for more flexibility (and complexity) where occasionally required.

The TM-2030 can also monitor the voltage only of a second battery, such as a starting battery, or possibly also the input voltage of a solar array (if less than 100 volts.).

This also provides lightning protection for the TM-2020. The TM-2020 will operate with 12 or 24 V systems, but requires the addition of the “TM-48VA” Adapter and lightning protection board when using it with 48V battery systems.

The TM-2030 will operate with (nominal) battery systems from 12 to 48V.

The TM2030 has some minimal data logging, which can be useful for a technician to diagnose some common setup or operational problems with battery systems.

The TM2030 is easier for you to program the necessary system parameters.

How many days since the batteries were fully charged: to remind you to not wait too long between fully charging your batteries to maximize their life.

Energy going in, or out of your batteries, measured in amps or watts, so you can see that your charging sources are charging properly, or how much current your loads are using.

Volts of the batteries, for example to check that they are being charged at proper voltage.

“Percent Full” (“State of charge”) of your batteries, so you can see if you need to charge them more, or check that overall usage is less than your charging resources.

A SHUNT is required, and which in some systems is already installed.Īll models are designed to monitor the following: They will help you maintain your batteries.

TRIMETRIC 2030 RV BATTERY SYSTEM MONITOR GENERATOR

The TriMetric is used to monitor battery systems used in remote homes, RVs or boats that have batteries that store solar, wind, or possibly generator powered chargers.